Zoneline Device¶
Tip: Use this navigation sections and page links to navigate easier.
Description¶
Zoneline/PTAC appliance.
| Label | Value |
|---|---|
| Device Type | cloud.smarthq.device.ptac |
| Connection Type | cloud.smarthq.connection.wifi |
| Icon Type | cloud.smarthq.icon.ptac |
| Product Name | Zoneline |
Alerts¶
AlertType |
Description |
|---|---|
| Common Alerts List | A list of alerts common across all SmartHQ devices that this device might support. |
Service Alerts¶
AlertType |
Description |
|---|---|
cloud.smarthq.alert.fault.coil.freeze.inside |
The indoor coil is too cold and is freezing. |
cloud.smarthq.alert.fault.coil.overheat.inside |
The temperature of the indoor coil over the high threshold. |
cloud.smarthq.alert.fault.compressor |
Alert when the compressor is no longer cooling or heating. |
cloud.smarthq.alert.fault.cooling.lockout |
The outdoor ambient temperature is too low for cooling mode to operate. |
cloud.smarthq.alert.fault.defrost.abnormal |
The heat pump operation has been locked out because the outdoor coil was not successfully defrosted. |
cloud.smarthq.alert.fault.eev.malfunction |
The refrigerant electronic expansion valve (EEV) is not operating properly. |
cloud.smarthq.alert.fault.heater.airflow |
The main board detects too low of indoor fan speed and shuts off the heater. |
cloud.smarthq.alert.fault.blower.lockedrotor |
The inside fan's rotor is locked. |
cloud.smarthq.alert.fault.thermistor.indoor |
The inside temperature sensor is experiencing a fault. |
cloud.smarthq.alert.fault.inverter.compressor |
The inverter compressor control board has an internally set fault. |
cloud.smarthq.alert.fault.muam |
The make-up air module has an internally set fault. |
cloud.smarthq.alert.fault.muam.ventdoor |
The make-up air vent door is not operating properly. |
cloud.smarthq.alert.fault.thermistor.outdoor |
The outdoor thermistor is experiencing a fault. |
cloud.smarthq.alert.fault.outlet.overheat.permanent |
Alert when the temporary outlet overheat fault has occurred repeatedly. Heater operation is locked out until the device has been serviced. |
cloud.smarthq.alert.fault.outlet.overheat.temporary |
The outlet air thermistor temperature has exceeded an upper limit. Heater operation is locked out until temperatures cool down. |
cloud.smarthq.alert.fault.condenser.lockedrotor |
The outside fan's rotor is locked. |
cloud.smarthq.alert.fault.overheat.inside |
The inside air thermistor has detected excessively high temperatures. |
cloud.smarthq.alert.fault.reversingvalve |
The unit is cooling the room when heat pump is requested, or heating the room when cooling is requested. |
cloud.smarthq.alert.fault.software |
There is an internal fault in main board. |
cloud.smarthq.alert.fault.thermistor.coilvapor.inside |
The indoor coil vapor temperature thermistor has failed. |
cloud.smarthq.alert.fault.thermistor.coilvapor.outside |
The outdoor coil vapor temperature thermistor has failed. |
cloud.smarthq.alert.fault.thermistor.outlet |
The thermistor outlet is experiencing a fault. |
cloud.smarthq.alert.fault.thermostat.external |
External thermostat fault detected |
Services¶
This device may not support each service listed. What is listed is all the possible services for this device. Learn more
Services |
Description |
|---|---|
| Zoneline Aux Constant Fan Toggle Service | Zoneline auxiliary setting for Constant Fan Mode. |
| Zoneline Aux Duct Mode Toggle Service | Zoneline auxiliary setting for Duct Mode. |
| Zoneline Aux External Thermostat Toggle Service | Zoneline auxiliary setting for External Thermostat Mode. |
| Zoneline Aux Fan Boost Toggle Service | Zoneline auxiliary setting for fan boost. |
| Zoneline Aux Freeze Protection Toggle Service | Zoneline auxiliary setting for Freeze Sentinel. |
| Zoneline Aux Heat Boost Toggle Service | Zoneline auxiliary setting for Heat Boost. |
| Zoneline Aux Heat Mode Service | Zoneline auxiliary setting for heat mode. |
| Zoneline Aux Heat Protection Toggle Service | Zoneline auxiliary setting for Heat Sentinel. |
| Zoneline Aux Heat Pump Toggle Service | Zoneline auxiliary setting for Electric Heat Only Mode. |
| Zoneline Aux Makeup Air Fan Speed Integer Service | Zoneline auxiliary setting for Makeup Air Module Fan Speed. |
| Zoneline Aux Makeup Air Filter Mode Service | Zoneline auxiliary setting for makeup air filter type. |
| Zoneline Aux Makeup Air Occupancy Toggle Service | Zoneline auxiliary setting for Makeup Air Module Occupancy Detection. |
| Zoneline Aux Smart Fan Cooling Mode Service | Zoneline auxiliary setting for Cooling Smart Fan Mode. |
| Zoneline Aux Smart Fan Heating Mode Service | Zoneline auxiliary setting for Heating Smart Fan Mode. |
| Zoneline Auxiliary Input Mode Service | Zoneline auxiliary input setting. |
| Zoneline Blower Speed Integer Service | Current inside fan speed in rpm |
| Zoneline Blower Speed Target Integer Service | Current target inside fan speed in rpm |
| Zoneline Central Desk Control Toggle Service | Zoneline central desk control - if set unit operation is suspended. |
| Zoneline Coil Sensor Outdoor Temperature Service | Coil Sensor Outdoor Temperature |
| Zoneline Condenser Speed Integer Service | Current outside fan speed in rpm |
| Zoneline Condenser Speed Target Integer Service | Current target outside fan speed in rpm |
| Zoneline Dehumidifier Mode Service | Zoneline auxiliary setting for dehumidification mode. |
| Zoneline External Control Input Override Integer Service | Allows Assertion of External Control Inputs |
| Zoneline Humidity Current Integer Service | Current Humidity Percentage |
| Zoneline Indoor Ambient Temperature Service | Indoor ambient temperature. |
| Zoneline Outdoor Ambient Temperature Service | Indoor ambient temperature. |
| Zoneline Temperature Coil Indoor Temperature Service | Indoor temperature coil. |
| Zoneline Temperature Coil Vapor Indoor Temperature Service | Indoor temperature coil vapor. |
| Zoneline Temperature Coil Vapor Outdoor Temperature Service | Outdoor temperature coil vapor. |
| Zoneline Thermostat V1 Service | Zoneline thermostat settings. |
| Zoneline Thermostat Wiring Integer Service | The zoneline thermostat wiring signals. |
| Zoneline U V C Kit Support Toggle Service | Enable UVC Kit Support |
| Common Services List | A list of services common across all SmartHQ devices that this device might support. |
Zoneline Aux Constant Fan Toggle Service¶
Description: Zoneline auxiliary setting for Constant Fan Mode.
Tuple: Controls Zoneline auxiliary setting for constant fan
| Attribute | Value | Description |
|---|---|---|
| ServiceType | cloud.smarthq.service.toggle | Service to model a binary state that can be read only or remotely controlled |
| DomainType | cloud.smarthq.domain.continuous |
The continuous |
| ServiceDeviceType | cloud.smarthq.device.fan |
A fan device |
Commands¶
| Command | Description |
|---|---|
| cloud.smarthq.command.toggle.set | Set the Constant Fan mode to cycle or continuous. |
Zoneline Aux Duct Mode Toggle Service¶
Description: Zoneline auxiliary setting for Duct Mode.
Tuple: Controls Zoneline auxiliary setting for duct mode
| Attribute | Value | Description |
|---|---|---|
| ServiceType | cloud.smarthq.service.toggle | Service to model a binary state that can be read only or remotely controlled |
| DomainType | cloud.smarthq.domain.ducted |
The ducted |
| ServiceDeviceType | cloud.smarthq.device.ptac |
A PTAC (Packaged terminal air conditioner) device. |
Commands¶
| Command | Description |
|---|---|
| cloud.smarthq.command.toggle.set | Enable or disable the Zoneline Duct Mode. |
Zoneline Aux External Thermostat Toggle Service¶
Description: Zoneline auxiliary setting for External Thermostat Mode.
Tuple: Controls Zoneline auxiliary setting for external thermostat
| Attribute | Value | Description |
|---|---|---|
| ServiceType | cloud.smarthq.service.toggle | Service to model a binary state that can be read only or remotely controlled |
| DomainType | cloud.smarthq.domain.external |
The external |
| ServiceDeviceType | cloud.smarthq.device.thermostat |
A thermostat device |
Commands¶
| Command | Description |
|---|---|
| cloud.smarthq.command.toggle.set | Enable or disable an external thermostat on the Zoneline. |
Zoneline Aux Fan Boost Toggle Service¶
Description: Zoneline auxiliary setting for fan boost.
Tuple: Controls Zoneline auxiliary setting for fan boost
| Attribute | Value | Description |
|---|---|---|
| ServiceType | cloud.smarthq.service.toggle | Service to model a binary state that can be read only or remotely controlled |
| DomainType | cloud.smarthq.domain.boost |
The boost |
| ServiceDeviceType | cloud.smarthq.device.fan |
A fan device |
Commands¶
| Command | Description |
|---|---|
| cloud.smarthq.command.toggle.set | Enable or disable a fan boost on the Zoneline. |
Zoneline Aux Freeze Protection Toggle Service¶
Description: Zoneline auxiliary setting for Freeze Sentinel.
Tuple: Controls Zoneline auxiliary setting for heat sentinel
| Attribute | Value | Description |
|---|---|---|
| ServiceType | cloud.smarthq.service.toggle | Service to model a binary state that can be read only or remotely controlled |
| DomainType | cloud.smarthq.domain.minimum.safe |
The safe minimum |
| ServiceDeviceType | cloud.smarthq.device.heater |
A heater device |
Commands¶
| Command | Description |
|---|---|
| cloud.smarthq.command.toggle.set | Enable or disable Freeze Sentinel on the Zoneline. |
Zoneline Aux Heat Boost Toggle Service¶
Description: Zoneline auxiliary setting for Heat Boost.
Tuple: Controls Zoneline auxiliary setting for heat boost
| Attribute | Value | Description |
|---|---|---|
| ServiceType | cloud.smarthq.service.toggle | Service to model a binary state that can be read only or remotely controlled |
| DomainType | cloud.smarthq.domain.boost |
The boost |
| ServiceDeviceType | cloud.smarthq.device.heatpump |
A heat pump device |
Commands¶
| Command | Description |
|---|---|
| cloud.smarthq.command.toggle.set | Enable or disable Heat Boost mode on the Zoneline. |
Zoneline Aux Heat Mode Service¶
Description: Zoneline auxiliary setting for heat mode.
Tuple: Controls Zoneline auxiliary setting for heating mode
| Attribute | Value | Description |
|---|---|---|
| ServiceType | cloud.smarthq.service.mode | Service to model a mode that represents a selection from a pre-defined list of options. The available options are defined by an enumeration and then the service config selects which of those are available. |
| DomainType | cloud.smarthq.domain.operating |
The operating |
| ServiceDeviceType | cloud.smarthq.device.heater |
A heater device |
Commands¶
| Command | Description |
|---|---|
| cloud.smarthq.command.mode.set | Set the heat mode on Zoneline. |
Zoneline Aux Heat Protection Toggle Service¶
Description: Zoneline auxiliary setting for Heat Sentinel.
Tuple: Controls Zoneline auxiliary setting for cool sentinel
| Attribute | Value | Description |
|---|---|---|
| ServiceType | cloud.smarthq.service.toggle | Service to model a binary state that can be read only or remotely controlled |
| DomainType | cloud.smarthq.domain.maximum.safe |
The safe maximum |
| ServiceDeviceType | cloud.smarthq.device.airconditioner |
An air conditioner device |
Commands¶
| Command | Description |
|---|---|
| cloud.smarthq.command.toggle.set | Enable or disable Heat Sentinel on the Zoneline. |
Zoneline Aux Heat Pump Toggle Service¶
Description: Zoneline auxiliary setting for Electric Heat Only Mode.
Tuple: Controls Zoneline auxiliary setting for heat pump
| Attribute | Value | Description |
|---|---|---|
| ServiceType | cloud.smarthq.service.toggle | Service to model a binary state that can be read only or remotely controlled |
| DomainType | cloud.smarthq.domain.available |
The available |
| ServiceDeviceType | cloud.smarthq.device.heatpump |
A heat pump device |
Commands¶
| Command | Description |
|---|---|
| cloud.smarthq.command.toggle.set | Enable or disable All Electric Heat Only mode on the Zoneline. |
Zoneline Aux Makeup Air Fan Speed Integer Service¶
Description: Zoneline auxiliary setting for Makeup Air Module Fan Speed.
Tuple: The makeup air module fan speed
| Attribute | Value | Description |
|---|---|---|
| ServiceType | cloud.smarthq.service.integer | Service to model a signed 32-bit integer value with associated units. |
| DomainType | cloud.smarthq.domain.makeupair.speed |
The makeup air speed |
| ServiceDeviceType | cloud.smarthq.device.fan |
A fan device |
Commands¶
| Command | Description |
|---|---|
| cloud.smarthq.command.integer.set | Set the Makeup Air Module Fan Speed. |
Behaviors¶
| Behavior | Description |
|---|---|
cloud.smarthq.behavior.zonelinemakeupairfanspeedsv1 |
Supported fan speeds are 0, 25, 30, 35, 40, 45, 50 CFM |
Zoneline Aux Makeup Air Filter Mode Service¶
Description: Zoneline auxiliary setting for makeup air filter type.
Tuple: The makeup air module fan filter type
| Attribute | Value | Description |
|---|---|---|
| ServiceType | cloud.smarthq.service.mode | Service to model a mode that represents a selection from a pre-defined list of options. The available options are defined by an enumeration and then the service config selects which of those are available. |
| DomainType | cloud.smarthq.domain.makeupair.filter |
The makeup air filter |
| ServiceDeviceType | cloud.smarthq.device.fan |
A fan device |
Commands¶
| Command | Description |
|---|---|
| cloud.smarthq.command.mode.set | Set the makeup air filter type on Zoneline. |
Zoneline Aux Makeup Air Occupancy Toggle Service¶
Description: Zoneline auxiliary setting for Makeup Air Module Occupancy Detection.
Tuple: Controls Zoneline auxiliary setting for makeup air mode occupancy detection
| Attribute | Value | Description |
|---|---|---|
| ServiceType | cloud.smarthq.service.toggle | Service to model a binary state that can be read only or remotely controlled |
| DomainType | cloud.smarthq.domain.makeupair.occupancy |
The makeup air occupancy |
| ServiceDeviceType | cloud.smarthq.device.fan |
A fan device |
Commands¶
| Command | Description |
|---|---|
| cloud.smarthq.command.toggle.set | Enable or disable the Makeup Air Module Occupancy Dectection. |
Zoneline Aux Smart Fan Cooling Mode Service¶
Description: Zoneline auxiliary setting for Cooling Smart Fan Mode.
Tuple: Controls Zoneline auxiliary setting for smart fan cooling
| Attribute | Value | Description |
|---|---|---|
| ServiceType | cloud.smarthq.service.mode | Service to model a mode that represents a selection from a pre-defined list of options. The available options are defined by an enumeration and then the service config selects which of those are available. |
| DomainType | cloud.smarthq.domain.operating |
The operating |
| ServiceDeviceType | cloud.smarthq.device.airconditioner.fan |
An air conditioner fan sub-device. |
Commands¶
| Command | Description |
|---|---|
| cloud.smarthq.command.mode.set | Toggle the Cooling Smart Fan Mode on the Zoneline. |
Zoneline Aux Smart Fan Heating Mode Service¶
Description: Zoneline auxiliary setting for Heating Smart Fan Mode.
Tuple: Controls Zoneline auxiliary setting for smart fan heating
| Attribute | Value | Description |
|---|---|---|
| ServiceType | cloud.smarthq.service.mode | Service to model a mode that represents a selection from a pre-defined list of options. The available options are defined by an enumeration and then the service config selects which of those are available. |
| DomainType | cloud.smarthq.domain.operating |
The operating |
| ServiceDeviceType | cloud.smarthq.device.heater.fan |
A heater fan sub-device |
Commands¶
| Command | Description |
|---|---|
| cloud.smarthq.command.mode.set | Toggle the Heating Smart Fan Mode on the Zoneline. |
Zoneline Auxiliary Input Mode Service¶
Description: Zoneline auxiliary input setting.
Tuple: The auxiliary input configuration on a Zoneline
| Attribute | Value | Description |
|---|---|---|
| ServiceType | cloud.smarthq.service.mode | Service to model a mode that represents a selection from a pre-defined list of options. The available options are defined by an enumeration and then the service config selects which of those are available. |
| DomainType | cloud.smarthq.domain.auxiliary |
The auxiliary |
| ServiceDeviceType | cloud.smarthq.device.ptac |
A PTAC (Packaged terminal air conditioner) device. |
Commands¶
| Command | Description |
|---|---|
| cloud.smarthq.command.mode.set | Set the auxiliary input configuration on Zoneline. |
Zoneline Blower Speed Integer Service¶
Description: Current inside fan speed in rpm
Tuple: The blower fan's speed
| Attribute | Value | Description |
|---|---|---|
| ServiceType | cloud.smarthq.service.integer | Service to model a signed 32-bit integer value with associated units. |
| DomainType | cloud.smarthq.domain.blower.speed |
The blower speed |
| ServiceDeviceType | cloud.smarthq.device.fan |
A fan device |
Zoneline Blower Speed Target Integer Service¶
Description: Current target inside fan speed in rpm
Tuple: The blower fan's target speed
| Attribute | Value | Description |
|---|---|---|
| ServiceType | cloud.smarthq.service.integer | Service to model a signed 32-bit integer value with associated units. |
| DomainType | cloud.smarthq.domain.blower.speed.target |
The target blower speed |
| ServiceDeviceType | cloud.smarthq.device.fan |
A fan device |
Zoneline Central Desk Control Toggle Service¶
Description: Zoneline central desk control - if set unit operation is suspended.
Tuple: Toggle for the central desk control
| Attribute | Value | Description |
|---|---|---|
| ServiceType | cloud.smarthq.service.toggle | Service to model a binary state that can be read only or remotely controlled |
| DomainType | cloud.smarthq.domain.centraldeskcontrol |
The Central Desk Control |
| ServiceDeviceType | cloud.smarthq.device.ptac |
A PTAC (Packaged terminal air conditioner) device. |
Zoneline Coil Sensor Outdoor Temperature Service¶
Description: Coil Sensor Outdoor Temperature
Tuple: The outdoor PTAC coil temperature
| Attribute | Value | Description |
|---|---|---|
| ServiceType | cloud.smarthq.service.temperature | Service to model a temperature that can be read only or remotely controlled. Both Celsius and Fahrenheit are supported and automatically converted using calculated properties. |
| DomainType | cloud.smarthq.domain.outdoor |
The outdoor |
| ServiceDeviceType | cloud.smarthq.device.ptac.coil |
A PTAC (Packaged terminal air conditioner) coil device. |
Zoneline Condenser Speed Integer Service¶
Description: Current outside fan speed in rpm
Tuple: The condenser fan's speed
| Attribute | Value | Description |
|---|---|---|
| ServiceType | cloud.smarthq.service.integer | Service to model a signed 32-bit integer value with associated units. |
| DomainType | cloud.smarthq.domain.condenser.speed |
The condenser speed |
| ServiceDeviceType | cloud.smarthq.device.fan |
A fan device |
Zoneline Condenser Speed Target Integer Service¶
Description: Current target outside fan speed in rpm
Tuple: The condenser fan's target speed
| Attribute | Value | Description |
|---|---|---|
| ServiceType | cloud.smarthq.service.integer | Service to model a signed 32-bit integer value with associated units. |
| DomainType | cloud.smarthq.domain.condenser.speed.target |
The target condenser speed |
| ServiceDeviceType | cloud.smarthq.device.fan |
A fan device |
Zoneline Dehumidifier Mode Service¶
Description: Zoneline auxiliary setting for dehumidification mode.
Tuple: Controls Zoneline auxiliary setting for dehumidifier mode
| Attribute | Value | Description |
|---|---|---|
| ServiceType | cloud.smarthq.service.mode | Service to model a mode that represents a selection from a pre-defined list of options. The available options are defined by an enumeration and then the service config selects which of those are available. |
| DomainType | cloud.smarthq.domain.operating |
The operating |
| ServiceDeviceType | cloud.smarthq.device.dehumidifier |
A dehumidifier device |
Commands¶
| Command | Description |
|---|---|
| cloud.smarthq.command.mode.set | Set the dehumidification mode on Zoneline. |
Zoneline External Control Input Override Integer Service¶
Description: Allows Assertion of External Control Inputs
Tuple: The signal override for a thermostat
| Attribute | Value | Description |
|---|---|---|
| ServiceType | cloud.smarthq.service.integer | Service to model a signed 32-bit integer value with associated units. |
| DomainType | cloud.smarthq.domain.signal.override |
The signal override |
| ServiceDeviceType | cloud.smarthq.device.thermostat |
A thermostat device |
Zoneline Humidity Current Integer Service¶
Description: Current Humidity Percentage
Tuple: Current Humidity Percentage
| Attribute | Value | Description |
|---|---|---|
| ServiceType | cloud.smarthq.service.integer | Service to model a signed 32-bit integer value with associated units. |
| DomainType | cloud.smarthq.domain.humidity.ambient |
The humidity ambient |
| ServiceDeviceType | cloud.smarthq.device.ptac |
A PTAC (Packaged terminal air conditioner) device. |
Zoneline Indoor Ambient Temperature Service¶
Description: Indoor ambient temperature.
Tuple: The ambient indoor PTAC temperature
| Attribute | Value | Description |
|---|---|---|
| ServiceType | cloud.smarthq.service.temperature | Service to model a temperature that can be read only or remotely controlled. Both Celsius and Fahrenheit are supported and automatically converted using calculated properties. |
| DomainType | cloud.smarthq.domain.indoor.ambient |
The indoor ambient |
| ServiceDeviceType | cloud.smarthq.device.ptac |
A PTAC (Packaged terminal air conditioner) device. |
Zoneline Outdoor Ambient Temperature Service¶
Description: Indoor ambient temperature.
Tuple: The ambient PTAC outdoor temperature
| Attribute | Value | Description |
|---|---|---|
| ServiceType | cloud.smarthq.service.temperature | Service to model a temperature that can be read only or remotely controlled. Both Celsius and Fahrenheit are supported and automatically converted using calculated properties. |
| DomainType | cloud.smarthq.domain.outdoor.ambient |
The outdoor ambient |
| ServiceDeviceType | cloud.smarthq.device.ptac |
A PTAC (Packaged terminal air conditioner) device. |
Zoneline Temperature Coil Indoor Temperature Service¶
Description: Indoor temperature coil.
Tuple: The indoor PTAC coil temperature
| Attribute | Value | Description |
|---|---|---|
| ServiceType | cloud.smarthq.service.temperature | Service to model a temperature that can be read only or remotely controlled. Both Celsius and Fahrenheit are supported and automatically converted using calculated properties. |
| DomainType | cloud.smarthq.domain.indoor |
The indoor |
| ServiceDeviceType | cloud.smarthq.device.ptac.coil |
A PTAC (Packaged terminal air conditioner) coil device. |
Zoneline Temperature Coil Vapor Indoor Temperature Service¶
Description: Indoor temperature coil vapor.
Tuple: The indoor vapor PTAC coil temperature
| Attribute | Value | Description |
|---|---|---|
| ServiceType | cloud.smarthq.service.temperature | Service to model a temperature that can be read only or remotely controlled. Both Celsius and Fahrenheit are supported and automatically converted using calculated properties. |
| DomainType | cloud.smarthq.domain.indoor.vapor |
The indoor vapor |
| ServiceDeviceType | cloud.smarthq.device.ptac.coil |
A PTAC (Packaged terminal air conditioner) coil device. |
Zoneline Temperature Coil Vapor Outdoor Temperature Service¶
Description: Outdoor temperature coil vapor.
Tuple: The outdoor vapor PTAC coil temperature
| Attribute | Value | Description |
|---|---|---|
| ServiceType | cloud.smarthq.service.temperature | Service to model a temperature that can be read only or remotely controlled. Both Celsius and Fahrenheit are supported and automatically converted using calculated properties. |
| DomainType | cloud.smarthq.domain.outdoor.vapor |
The outdoor vapor |
| ServiceDeviceType | cloud.smarthq.device.ptac.coil |
A PTAC (Packaged terminal air conditioner) coil device. |
Zoneline Thermostat V1 Service¶
Description: Zoneline thermostat settings.
Tuple: The thermostat control for a PTAC
| Attribute | Value | Description |
|---|---|---|
| ServiceType | cloud.smarthq.service.thermostat.v1 | Service for controlling a thermostat. This is a complex service with multiple config and state parameters to accurately model the control of an air conditioner or heater. |
| DomainType | cloud.smarthq.domain.thermostat |
The thermostat |
| ServiceDeviceType | cloud.smarthq.device.ptac |
A PTAC (Packaged terminal air conditioner) device. |
Commands¶
| Command | Description |
|---|---|
| cloud.smarthq.command.thermostat.v1.set | Control the thermostat settings on the Zoneline. |
| cloud.smarthq.command.thermostat.v1.set.maximum | Set the maximum heat temperature on the Zoneline. |
| cloud.smarthq.command.thermostat.v1.set.minimum | Set the minimum cooling temperature on the Zoneline. |
Behaviors¶
| Behavior | Description |
|---|---|
cloud.smarthq.behavior.fanonlynoauto |
When in fan only mode the auto fanSpeed does not work |
cloud.smarthq.behavior.zonelineminimumtemperaturesv1 |
Supported minimum temperatures are 60F, 64F, 66F, 68F, 70F, 72F, 74F, 76F |
cloud.smarthq.behavior.zonelinemaximumtemperaturesv1 |
Supported maximum temperatures are 65F, 70F, 72F, 74F, 76F, 78F, 80F, 85F |
Zoneline Thermostat Wiring Integer Service¶
Description: The zoneline thermostat wiring signals.
Tuple: The thermostat wiring signals
| Attribute | Value | Description |
|---|---|---|
| ServiceType | cloud.smarthq.service.integer | Service to model a signed 32-bit integer value with associated units. |
| DomainType | cloud.smarthq.domain.signal |
The signal |
| ServiceDeviceType | cloud.smarthq.device.thermostat |
A thermostat device |
Behaviors¶
| Behavior | Description |
|---|---|
cloud.smarthq.behavior.zonelinethermostatsignals |
Zoneline external thermostat wiring signal |
Zoneline U V C Kit Support Toggle Service¶
Description: Enable UVC Kit Support
Tuple: Toggles the Light UVC to be available
| Attribute | Value | Description |
|---|---|---|
| ServiceType | cloud.smarthq.service.toggle | Service to model a binary state that can be read only or remotely controlled |
| DomainType | cloud.smarthq.domain.available |
The available |
| ServiceDeviceType | cloud.smarthq.device.light.uvc |
A UVC light device |
Commands¶
| Command | Description |
|---|---|
| cloud.smarthq.command.toggle.set | Enable or disable UVC Kit support |